Using a torque wrench and 24mm (15/16”) socket, tighten the banjo bolt to 25 ft lbs. Optional: If you are installing an oil gauge, remove the 1/8” NTP plug and install the sensor. Start your engine and make sure that there are no oil leaks. If any exist, recheck that the banjo bolt is properly installed and tight.
Rotary Engine Rebuild Tolerences & Torque Settings
Mar 15, 2004 · 13B torque settings . Counterweight/Flywheel nut.....290-360(ft/lb) Flex plate to counterweight (auto).....32-45 (ft/lb) ... Oil Pan Bolts.....5.8-8.0 (ft/lb) Oil Pump to Engine bolts.....5.1-7.2 (ft/lb) ... Torque specs - 12a Rx7. by 78mg » Mon Nov 09, 2020 9:16 pm » in Tech Talk. 4 Replies 3716 Views
Oil line can be adjusted for alignment at oil line bracket located at the bottom driver side of the front housing. Hand thread two crush washers and banjo bolt into oil pedestal. **Install one sealing washer per banjo side.** Torque banjo bolt to 50-60 ft lbs. Lubricate oil filter o-ring and install onto pedestal. Start car and check for ...
FAQ/Bolt Thread and Pitch List [Archive] - Rotary Car Club
Sep 6, 2018 · P/S Banjo Bolt: 10mm fine thread (go into the end of the steering link, from the pump) Front Differential Mount Studs: M12 x 1.50 (same as lug nuts) Rear Differential Mount Studs: M12 x 1.25
Torque specs - 12a Rx7 - AusRotary
Nov 11, 2020 · I'm happy to run with the bolts. I've tightened the bolts on the engine mount bracket to front cover to 30 ft-lb, which is towards the bottom of the range for 8T 10mm bolts described by Kypreo. Given the front cover is a bit softer, it makes sense to me to keep it at the bottom of that range.
DIY: Oil Pressure and Temp sender install with Rx8performance.com banjo …
Jul 17, 2012 · 3: attach oil pressure sender to the new banjo bolt, being sure to apply teflon tape to the sender threading 4: put a new crush washer onto the new bolt, slide it through the oil line, place another new crush washer onto the bolt and bolt it to the front cover. the torque is 24 ftlbs.
87-91 Turbo Rx7 Oil Feed Banjo Bolt to Front Side Housing (9936 …
Banjo bolt in the top of the front side housing iron. Connects the oil feed line to the turbo for all 87-91 Turbo Mazda Rx7s. Don't forget your crush washers , two per banjo fitting.
PRESS RELEASE MADNESS: FOUR PRODUCTS; ONE POST!
May 2, 2011 · We have tested this part to work perfectly with the OEM oil cooler lines as well as our CorkSport brand Stainless Steel Braided Oil Cooler Lines. The bolt installs in minutes with simple hand tools (23mm wrench, socket, & torque wrench) in minutes.
r/RX7 on Reddit: Where can I find the specs for all the nuts, bolts ...
Sep 13, 2017 · Slightly longer and you have the bolt length for things like pulley bolts. There's a trick in this thread detailing how to read bolt lengths off Mazda part numbers if you can be arsed to dig through the Mazda OEM parts catalogs: https://www.rx7club.com/3rd-generation-specific-1993-2002-16/bolt-nut-sizes-various-parts-1002504/
79-11 Rx7 & Rx8 Oil Cooler Line Banjo Bolt (9938-11-400)
Check if this part fits your vehicle. Also fits the 90-95 20B Cosmo. Don't forget the oil cooler line crush washers. M18x1.5mm.
- Some results have been removed